GETTING THE MOST FROM YOUR
CARPET
Your new carpet represents a substantial investment
and, like your other fine furnishings, requires proper care to
keep it attractive over the years to come. You can protect your
investment, prolong the life of your carpet, and enhance the quality
of the indoor environment by establishing a regular maintenance
schedule.
Carpet rarely wears out in terms of fiber wearing away,rather
its appearance simply deteriorates over time to a point at which
it is no longer acceptable. Experience has shown that proper maintenance
can help reduce the rate in which a carpets appearance changes.
The information in this page pertains to carpets made of synthetic,
or man-made, fibers and may not be appropriate for natural fibers
such as wool.
THE CARPET CARE PROGRAM Basic 4
A comprehensive carpet care program consists of four elements:
1) Preventive Maintenance | ![]() |
![]() |
2) Regular vacuuming. | ||
3) Spot and Spill Removal. | ![]() |
![]() |
4) Cleaning Overall on a regular basis. |
PREVENTIVE
MAINTENANCE
1 ) Walk-off mats should be used at all entrances to absorb
soil and moisture, and mats should be cleaned on a regular basis
so they don't become sources of soil themselves, especially during
inclement weather.Try to keep your sidewalks and entrance ways
free of excessive dirt and substances which can be tracked into
the home.
2) Use a quality pad under your carpet, particularly on
stairs. Good pad not only gives better resilience underfoot, but
it can also add to the life of your carpet.Some carpets carry
warranties with specific density and thickness requirements. Before
purchasing your carpet pad, review your warranty.
3) Move heavy furniture occasionally to avoid excessive
pile crushing. Put coasters intended for use with carpet under
the legs of tables, chairs, and other furniture to help distribute
the weight and prevent crushing the pile.Do not use chairs or
appliances with rollers or casters on carpet without a chair pad
designed for carpet.Continued use without a chair pad can cause
damage to the carpet.
4) When moving heavy wheeled furniture (pianos, buffets,etc.),
prevent damage by placing a protective barrier of heavy cardboard
or plywood between the wheels and the carpet.
5) If you use area rugs over your carpet, be sure to remove
and clean them regularly. Clean and restore the pile of the carpet
underneath. Be certain to check area rugs for colorfastness before
putting them back over carpet, as the dyes in some rugs may bleed
through to carpet. After cleaning your carpet, remember to allow
complete drying before replacing rugs.
6) Protect your carpet from prolonged periods of direct
sun-light with blinds, shades, or awnings.
NOTE: NO CARPET IS ABSOLUTELY STAIN PROOF.SOME CARPETS HAVE STAIN RESISTANT TREATMENTS TO IMPROVE YOUR ABILITY TO CLEAN UP STAINS, NOT PREVENT STAINS. CARPETS WITH SOIL RESISTANT TREATMENTS REDUCE THE RATE OF SOILING, BUT ALL CARPETS REQUIRE REGULAR CARE AND MAINTENANCE.
Stain Versus Soiling
It should be noted that there is often confusion about the difference
between soiling and staining, and the majority of stain complaints
are actually soil-related. For example, many sugar-based spills,
such as soft drinks and coffee, leave a sugar residue after removal;
this sticky residue readily attracts soil from ordinary shoe traffic,
and the resulting discolored area appears to be a stain. The same
thing happens when spills are cleaned with a detergent solution
and the area is not sufficiently rinsed with plain water, leaving
a sticky detergent residue. It is important to rinse thoroughly
with water and blot dry after removing any spill.
The most important step in caring for your carpet is vacuuming. Vacuum thoroughly and frequently, particularly in high-traffic areas. Bear in mind that walking on soiled carpet permits the soil particles to work their way below the surface of the pile where they are far more difficult to remove and can damage the fibers. Frequent vacuuming removes these particles from the surface before this happens.For rooms with light traffic, vacuum the traffic lanes twice weekly and the entire area once weekly. Those areas with heavier traffic require that the traffic lanes be vacuumed daily and the entire area twice weekly. Up to three passes of the machine will suffice for light soiling, but five to seven passes are necessary for heavily soiled areas. Change the vacuuming direction occasionally to help stand the pile upright and reduce matting.
Vacuum cleaner recommendations:
1) A good vacuum cleaner is vital to prolonging the beauty
and life of your carpet. An inexpensive machine can remove surface
dirt but will not effectively remove the hidden dirt and particles
embedded in the pile.
2) Shaw Industries recommends the use of vacuums with a
rotating brush or combination beater/brush bar that agitates the
carpet pile and mechanically loosens soil for removal by the vacuum.
Note that carpet with thick loop pile construction may be sensitive
to brushing or rubbing of the pile surface and may become fuzzy.
For these products, Shaw recommends the use of a suction-only
vacuum or a vacuum with an adjustable brush lifted away from the
carpet so it does not agitate the pile. A vacuum with a beater/brush
bar can be tested in an inconspicuous location and used if no
excessive fuzzing occurs.
3) Replaceable paper vacuum bags do a better job of trapping
the small particles that pass through cloth bags back into the
room. High efficiency vacuum bags, also called micro filtration
bags, trap even smaller microscopic particles such as mold and
mildew spores and dust mite byproducts, often found to be a source
of allergies. This type of bag is sold under several brands, such
as the"MICRO-LINED" bag available at most vacuum specially
shops, or the "MICRO- CLEAN" bag available at some department
and discount stores, and "MICRO- FILTRATION" and "MICROLIHER"
brands available at Sears stores. These bags are available under
other brand names; verify that these bags trap particles smaller
than two (2) microns. All vacuum bags should be checked often
and replaced when half full.
4) Make sure the belt is in good condition and that the
brush or beater bar rotates when in contact with the carpet. To
adjust the vacuum to the correct height setting for the carpet,
raise the beater/brush bar to the highest setting and then lower
it until it contacts the pile enough to slightly vibrate the carpet
several inches away from the machine, but not low enough to cause
significant slowing of the motor.
5) Change the vacuuming direction occasionally to help
stand the pile upright and help reduce matting.
SPOT AND SPILL REMOVAL
Skip to Specific Stain
Removal Procedures
A good checklist to handle spills should include the following
items. Do not use any household cleaners other than those listed,
since many household products contain chemicals that may permanently
damage your carpet.
1) A solution of a mild liquid
detergent (no more than 1/4 teaspoon of detergent to 32 ounces
of water). A clear,non-bleach liquid dish washing detergent such
as Dawn,Joy, or clear Ivory is recommended. Do not use deter-gents
that are cloudy or creamy because they may leave a sticky residue.
2) A solution of 1 part white
vinegar to 1 part water.
3) White cloths or white paper towels.
4) An ammonia solution of one
tablespoon of ammonia to one cup of water. Do not use on wool.
5) Non-oily nail polish remover.
6) Chewing gum remover (freeze or solid type).
7) Spot remover specifically for
grease, oil, or tar, such as Carbona or Energine.
NOTE: Difficult stains on carpets made from solution-dyed fibers such as polypropylene may be removed with a mild bleach solution (one part chlorine bleach to five parts water).
WARNING: Do not use bleach solution unless you are absolutely certain your carpet is 100% solution dyed.Carpet dyed by other systems will be damaged. If in doubt, call 1-800-441-SHAW.
General Instructions -
Prompt attention to spots and spills is essential.No carpet is
stain proof, although many are stain resistant. which allows lime
to act.
* Remove as much of food spills as possible by scraping gently
with a spoon or dull knife.
* Absorb wet spills as quickly as possible by blotting repeatedly
with white paper or cloth towels.
* Always blot; never rub or scrub abrasively, as a fuzzy area
may result. When blotting, work from the outer edge in toward
the center of the spot to avoid spreading the spill.
* Always follow up with water to remove detergent residue that
may become sticky and cause rapid resoiling.
* Draw out any remaining moisture by placing several layers of
white towels over the spot and weigh them down with a heavy object
that will not transfer color, such as a plastic jug of water.
Stain Removal
Procedures
The following recommendations should be used for spot cleaning.
The numbers are keyed to the stain, and all instructions should
be used in the recommended sequence. Some stains are marked PRO,
indicating that professional knowledge and equipment are necessary.
Go to- Specific Stain Removal Procedures
A. Water Soluble Stains- Absorb as much
as possible with white towels. Blot the stained area with white
towels dampened with cool water until there is no more transfer
of the stain onto the towels.
If any of the stain remains, use the detergent
solution previously described.
Spray lightly onto the spot and blot repeatedly with white towels,
working from the outer edge in toward the center of the spot to
avoid spreading.
Rinse thoroughly by spraying with clean water, and then blot or
extract. Do not use too much detergent because the residue will
contribute to rapid re-soiling.
A-1. As in A, but before using
detergent, apply the white vinegar solution
to a white towel and blot or spray onto spot.
A-2. As in A, but before using
detergent, apply a house-hold ammonia
solution to a white towel and blot or spray onto spot. Do
not use on wool or wool-blend carpet. Rinse as in A.
B. Oil-Based Stains-Blot as much as possible with white paper towels. Apply the special oil and grease spot remover to a paper towel and repeat blotting.(Protective gloves should be worn, as the solvent will quickly remove oils from the skin and could result in irritation.) Do not pour or spray directly on the carpet pile, as damage to the backing or adhesive underneath could result; use the towels to transport the sol-vent to the carpet. Repeat as often as necessary. Provide adequate ventilation! Do not use flammable solvents! Follow with procedures in A.
C. Freeze stains such as chewing gum and candle wax with ice or a commercially available product in an aerosol can. Shatter with a blunt object and vacuum before the chips soften. Follow up with solvent as in B.
D. Bleach -WARNING -Only carpets which are solution dyed are resistant to bleaching, but do not exceed the recommended concentration. DO NOT USE THIS PROCEDURE UNLESS YOU ARE ABSOLUTELY CERTAIN THE CARPET IS SOLUTION DYED -CARPETS DYED BY OTHER SYSTEMS WILL BE DAMAGED. Products with olefin and nylon blends can not be exposed to bleach without removing the color from the nylon fibers unless the nylon component is solution dyed. If in doubt, call 1-800-441 -SHAW.
For solution-dyed carpets with stains such as food dyes, fruit drink, and coffee not removed by A-l, use a solution of one part chlorine bleach to five parts water.
Rinse several times with water to remove excess bleach so that none is tracked to other areas where there is conventionally dyed carpet.
PRO - Professional cleaner.
Some stains are marked PRO, indicating that professional knowledge
and equipment are necessary.
|
REMOVAL PROCEDURES | ||
First | Next | Last | |
Alcoholic Beverages | A | ||
Asphalt | B | PRO | |
Beer | A | ||
Betadine | PRO | ||
Berries | A | ||
Blood (wet) | A | ||
Blood (dry) | A-2 | ||
Butter | B | ||
Chewing Gum | C | ||
Chocolate | A-2 | ||
Coffee | A-1 | (D if necessary) | |
Cola Drinks | A | ||
Cosmetics | A | (D if necessary) | |
Crayon | B | ||
De-icer (Calcium Chloride) | Vacuum, A | ||
Excrement | A | ||
Food Dyes | A | ||
Furniture Polish | A | B | PRO |
Glue (white) | A | ||
Gravy | A | ||
Grease (Auto) | B | PRO | |
Grease (Food) | B | ||
Ice Cream | A | ||
Ink (Ballpoint) | B | PRO | |
Ink Permanent | B | (D if necessary) | |
Ink (Washable) | A | PRO | |
Jelly | A | ||
Lipstick | B | ||
Milk | A | ||
Mud | A | ||
Mustard | A | (D if necessary) | |
Nail Polish | Polish Remover | ||
Paint (Latex, wet) | A | ||
Paint (Latex, dry) | B | ||
Paint (Oil) | B | PRO | |
Rust | PRO | ||
Shoe Polish | B | ||
Tea | A | (D if necessary) | |
Urine | A-1 | PRO | |
Vomit | A-1 | ||
Wax | C | ||
Wine | A-2 | ||
Warning: Certain products found in most homes can cause irreparable damage to your carpet. Bleaches, tile cleaners, mildew removers, oven cleaners, and drain openers are very strong chemicals that can discolor or dissolve carpet fibers. Acne medications containing benzoyl peroxide, a very powerful bleach, are capable of permanently damaging your carpet and most other fabrics as well. |
CLEANING Overall on a regular basis
Even though vacuuming can remove most of the dry soil, it is also necessary to clean your carpet on a regular basis to remove the oily, sticky soil that builds up in the pile as a result of cooking vapors, air pollution, and tracked in dirt from outside. The particles of oily soil deposited on carpet fibers can cause gradual but significant dulling of delicate pastel colors: the color isn't lost but is hidden under the Film. If this type of soil is allowed to accumulate, it begins to attract and hold the dry soil. This is the reason cleaning is so important when dulling of the color is first noticed; if allowed to remain too long, it becomes gummy and difficult to remove.If carpet is cleaned before it becomes too unsightly, the cleaning chore will be easier and more successful. It is a myth that cleaning the carpet before it is absolutely necessary will cause it to get dirty faster. Carpet in a typical household should be cleaned every 12 to 18 months depending upon the number of residents and amount and type of activity.Choice of the proper cleaning system is important. Some systems may leave residues which promote resoiling and defeat the whole purpose of cleaning. The recommendations below represent the best current knowledge and should help prolong the time between cleanings.
The cleaning system
Shaw Industries recommends the hot water extraction system, which
research indicates provides the best capability for cleaning.
This system is commonly referred to as"steam cleaning,"
although no steam is actually generated.The process consists of
spraying a solution of water and detergent into the carpet pile
and recovering the water and soil with a powerful vacuum into
a holding tank. This can be done from a truck-mounted unit outside
the home with only the hose and wand brought inside or, where
a truck-mounted unit cannot reach, by a portable, self- contained
system brought into the home.
Professional carpet cleaners
It is to your advantage to use professional cleaners because their
experience enables them to do a better job than you can do yourself.
Their equipment has more extraction power than the rental units
available to you, and the carpet should dry more quickly. True
professionals have also made the investment in training to understand
the equipment, to know the proper cleaning agents for the situation
at hand, and to recognize the differences in fibers and carpet
construction.
One way to locate a professional cleaner is to contact the Institute of Inspection, Cleaning and Restoration Certification (IICRC) at 1-800-835-4624, This organization maintains a national directory of independent professional cleaners who are trained and certified in a variety of cleaning specialties. Call and explain that you have purchased a Shaw Industries carpet, and be sure to ask for a cleaner near you who uses the hot water extraction system.
Do-it-yourself systems - If you decide to rent a steam cleaning machine and do it yourself, check several cleaning systems before making a selection. Most rental units avail-able do not adequately clean and may actually damage the carpet. Consider the following:
1) Some rental companies have cleaning equipment that is similar to what the professionals use. The cleaning equipment should have enough vacuum power to allow the carpet to dry within 6 to 12 hours after cleaning.Avoid rental units found in many retail and grocery stores that do not have enough power to extract the cleaning solution from the carpet adequately and which may actually damage the carpet due to over wetting.
2) Avoid over wetting the carpet. Prolonged dampness may promote growth of mildew and bacteria in the carpet or cause separation of the backing. A carpet that is wet for more than 24 hours could develop a growth of mold and mildew. This is controlled by a combination of proper equipment and operator training. Most problems in do-it-yourself cleaning are due to over wetting and use of excessive detergent.
3) Use a cleaning solution with a pH less than 10, prefer-ably near 9, and with a minimum of non-sticky residue.The attraction between the detergent and the particles of soil and oil is critical during the cleaning process.However, the detergent residue continues to attract the particles after cleaning. Increasing the amount of cleaning solution beyond the recommended level does not greatly increase cleaning performance, but makes the removal of detergent more difficult. Because buildup of detergent residue is the most common cause of accelerated re-soiling complaints, do not use extra cleaning solution. Shaw Industries recommends a clear water rinse after cleaning.
4) Carpet with stain resistant treatments must be cleaned with products formulated for this purpose, or the stain resistance will be impaired and the warranty voided.Do not use cleaning or spotting solutions that contain bleaches or optical brighteners because they can discolor the carpet.
5) Do not use any silicone-based anti-soil treatments on carpets produced by Shaw Industries. The only anti-soil products approved for use as needed are either DuPontTeflon* or 3M Scotchgard.6) Reduce drying time by using several fans to move air across the carpet in combination with a dehumidifier or air conditioner to pull moisture out of the air. Carpet should be dry within 12 hours; even less is better.
Bonnet cleaning systems -
Bonnet cleaning systems employ a rotating bonnet of terry
cloth or other absorbent material to agitate the carpet pile and
absorb soil. A detergent solution is sprayed onto the pile and
then worked with the bonnet attached to a rotary floor polisher.
Shaw industries does not recommend this cleaning system.
The bonnet system has very limited capability for soil removal
and leaves much of the detergent in the pile since it employs
no real extraction. As a result, rapid re-soiling often occurs.
Another disadvantage is that the spinning bonnet may distort the
fibers of cut pile carpet, fuzzing the pile and leaving distinct
swirl marks.